CP3525 Series and CM3530 MFP Teardown Checklist

惠普喷墨打印机、激光打印机、多功能一体机、扫描仪、绘图仪等

版主: xyevolve

版面规则
1. 本版是定位于惠普打印机产品的技术讨论区。
2. 本版鼓励发帖共同讨论技术问题,不鼓励站内信件私下交流,独知知不如众知知。
3. 本版允许转贴或引用他人的作品,但必须声明原作者信息。
4. 本版禁止发表出售、求购、或其他非技术讨论等帖子。
5. 本版禁止灌水,包括但不限于任何与所讨论主题无关的回复,无意义字符,直接复制其他回复等。
6. 本站附件禁止用于商业目的,请在下载后24小时内删除,本站不对其造成的结果负任何责任。
回复
admin
网站编辑
帖子: 767
注册时间: 2010年 12月 22日 04:06 星期三

CP3525 Series and CM3530 MFP Teardown Checklist

帖子 admin » 2014年 11月 18日 10:04 星期二

HP Color LaserJet CP3525 Series Printer and HP Color LaserJet CM3530 MFP Teardown Checklist

CSR removal

ADF and control panel
Remove and replace the ADF roller assembly (CM3530 MFP)
Identify the ADF separation pad
Remove and replace the ADF assembly (CM3530 MFP)
Remove the control panel overlay (CM3530 MFP)
Remove and replace the control panel (CM3530 MFP)
Remove the staple cartridge (CM3530 MFP)
Remove the print cartridges
Remove the toner collection unit (TCU)
Remove and replace the front door
Identify the cartridge lock
Identify the PGC actuator lever
Remove and replace the duplex reverse guide

Tray 2
Remove and replace the Tray 2 separation roller assembly
Identify the tray-present flag

Tray 3
Remove and replace the Tray 3 rollers
Remove and replace the Tray 3 right door

Formatter
Remove the formatter
Remove and replace the HDD
Remove and replace the DIMM
Remove and replace the fax card

Secondary transfer roller
Remove and replace the secondary transfer roller

ITB
Remove the ITB

Fuser
Remove the fuser

admin
网站编辑
帖子: 767
注册时间: 2010年 12月 22日 04:06 星期三

Re: CP3525 Series and CM3530 MFP Teardown Checklist

帖子 admin » 2014年 11月 18日 10:08 星期二

Product teardown

Remove the ADF and control panel if they have been reattached.

Scanner, SCB and convenience stapler (CM3530 MFP only)
Remove the scanner
Remove the SCB assembly
Remove and replace the convenience stapler
CAUTION: The stapler is always energized. To ensure that no power is present in the area you are servicing, unplug the MFP.
Reinstall the scanner, ADF, and the control panel.

Engine—right side
Remove the Tray 1 pick roller
Remove the right side door
Identify the supports and hinges
Identify duplex jam clearance
Identify the duplex drive gear
Identify the Tray 1 assembly
Identify the safety interlocks (5-volt and 24-volt)
Identify the secondary transfer ramp feature
Identify the handle latches that secure the door
Identify the Tray 3 paper path
Identify the Tray 1 separation pad
Identify the Tray 2 paper path jam clearance
Identify the registration assembly
Identify the fuser drive gear
Identify the fuser sensors
Identify the ITB alienation sensor
Identify the high voltage contact for secondary transfer
Identify the pre-exposure LEDs
Remove the RD sensor assembly

Engine—front
Remove the control panel (CP3525 Series Printer) or the front upper right cover (CM3530 MFP)
Remove the right front cover
Identify the remote switch PCA
Identify the two 5-volt interlock switches and the 24-volt switch
Identify the sensors in the upper right
Identify the PGCs
Identify the locks that secure the print cartridge (top and back)
Identify the drum ground connection
Identify the four spring contacts that engage with the ITB
Identify the latches that secure the front door
Identify the cooling ductwork
Identify the TCU full sensor
Identify the TCU motor
Identify the cave light
Remove the front inner cover
Identify the CK laser spring
Remove and replace a PGC actuator
Replace the front inner cover

Engine—remove covers
Remove the left side cover
Remove the right rear corner cover
Remove the back cover
Identify the fan and fan shroud
Identify the low voltage power supply (LVPS)
Identify the DC controller
Identify the engine test switch
Identify the ICB
Remove the engine handle
Remove the LVPS and formatter cage
Remove the ICB

DC controller (DCC)
Remove the right rear corner support bracket
Disconnect the cables from the DCC
Remove the DCC assembly
Identify the main drive assembly

High voltage power supply—developer and transfer (HVPS-D and HVPS-T)
Remove the HVPS-D
Identify the cassette pickup motor
Identify the Tray 2 lifter assembly
Remove the HVPS-T
Identify the fuser motor assembly
Identify the main drive assembly and three drum motors
Identify the developer alienation motor
Identify the FFCs that route to laser scanners
Identify the high voltage connection for transfer

Engine—left side and rear
Remove the sheet metal plate
Identify the YM laser scanner
Identify the environmental sensor
Identify the stapler power supply cable
Identify the TCU auger motor gears
Identify the TCU full sensor
Remove the fan unit
Remove the TCU full sensor
Remove the YM laser scanner
CAUTION: When reinstalling the YM laser scanner, be sure the FFC is properly seated. If it is not, it could blow a fuse on the DCC.
Replace the YM laser scanner, TCU full sensor, fan unit, and the left inner cover

Registration assembly
Remove the right side gear cover
Remove the registration assembly
Identify the connections
Note: Do not disconnect the registration assembly.
Replace the registration assembly

Main drive assembly
Remove the high voltage contact assembly
Remove the FFC wiring guide
Identify the support bracket for the DCC
Remove the alienation motor
Remove the main drive assembly
Remove the DCC support

admin
网站编辑
帖子: 767
注册时间: 2010年 12月 22日 04:06 星期三

Re: CP3525 Series and CM3530 MFP Teardown Checklist

帖子 admin » 2014年 11月 18日 10:09 星期二

Product reassembly

Replace the main drive assembly
Replace the HVPS-D
Replace the HVPS-T
Verify the FFC and one cable are properly routed above the HVPS-T
Verify another cable is connected at the top of the HVPS-T
Verify screws with washers were used to reattach HVPS-D and HVPS-T
Reattach the DCC assembly
Verify there are only 5 connectors that are not connected
Verify there is no screw at the lower right corner of the DCC assembly
Replace the right side gear cover
Replace the fan shroud and fan
Replace the LVPS/ICB/formatter cage assembly
Verify there are only two connections that are not connected on the DCC

STOP: Perform the engine test.
Complete the reassembly.

回复